Digital Link DL600E E1 Guide de l'utilisateur Page 96
- Page / 147
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
5-20 DL600E E1 Data Multiplexer UserÕs Guide
For more information about monitoring the DL600E unit, refer to ÒMenu-1
Main Status ParametersÓ
in Chapter 4.
Using the TEST Menu
You can perform the Self-Test, activate network loopbacks, test modes,
and
DTE loopbacks on the local DL600E unit from the front panel TEST
menu.
D
Note: The TEST menu does not appear on the front panel
display if the front panel is protected in Menu-4 Main
ConÞguration (
UNIT Protect mode is enabled).
Only the Network Loopback test can be run on the remote unit from the
TEST menu.
Starting and Ending a Test
You can run only one test at a time. To run another test, you must
terminate the first one.
1 To start a test, open the TEST menu and select the test from the
menu or one of the sub-menus.
If you select a test that applies to a fraction of the E1
bandwidth, you are prompted to specify the fraction.
MONITOR
CONFIGURATION
TEST
EFS 100 PERCENT
- DL600E E1 1
- Data Multiplexer 1
- UserÕs Guide 1
- Product Limited Warranty 4
- Disclaimer 5
- ISO Registration 5
- Table of Contents 7
- Table of Figures 11
- Table of Tables 13
- ¥ About this Manual xviii 15
- About this Manual 16
- Typographic Conventions 17
- Send Us Your Comments 19
- When Returning a Unit 19
- About the DL600E Unit 21
- Introducing the DL600E Unit 22
- About the DL600E Unit 1-3 23
- DL600E Features 24
- About the Telnet Utility 25
- Applications 25
- Installing 27
- Checking the Equipment 28
- Equipment Model Numbers 29
- Gathering Information 29
- About the Power Supply 30
- Warning! 31
- CAUTION: 33
- ConÞguring 35
- Preparing to ConÞgure 36
- Connection be set to 38
- Modem in Menu-8 Alarm II 38
- User Access Rights 40
- Logging on from a Terminal 40
- password a second time when 41
- IP address 42
- Logging off 43
- Before You Begin 43
- Using the Terminal Interface 43
- Setting a Parameter in a Menu 43
- Overview of the ConÞguration 43
- About the Remote System 44
- NET (the alternate clock 46
- Downloading New Software 47
- DOWNLOAD UTILITY 0.1 48
- Operational Software: 48
- Updated Download Utility: OK 48
- Factory Download Utility: OK 48
- Download RAM allocated: OK 48
- Description* 49
- Configuring the Data Port 50
- Allocating Timeslots 51
- Allocation Type 52
- Allocation Type in edit mode 52
- 2 To specify Data Port 1: 53
- 1 To select Manual 53
- Allocate by Port Þeld 54
- ConÞguring for SNMP 55
- Ñ public) 56
- Ñ public) 56
- Superuser Access Rights 57
- Assigning User Passwords 57
- ConÞguring Alarm Conditions 58
- ConÞguring Alarms 59
- Menu-7 Alarm I Parameters 60
- Example: 1.2 x 10 61
- Example: 61
- Menu-8 Alarm II Parameters 62
- 15 Min. 30 Min., Unlimited 63
- Monitoring and Managing 65
- Introduction 66
- Logging on to the DL600E 66
- In Other Conditions 68
- Logging Off 70
- Monitoring Status 70
- Menu-1 Main Status Parameters 71
- E1 signal 72
- DTR or RTS DTE lines, user 73
- Menu-2 Data DTE Status 74
- Data DTE Status Parameters 74
- Reports which displays 75
- CRC errors 76
- CRC is incremented 76
- Using the Front Panel 77
- Interface 77
- Front Panel Description 79
- ( ) and press ENTER 80
- Front Panel Keys 81
- Front Panel Key 81
- Editing a Parameter 82
- Required Information 83
- Keeping a Record 83
- UNIT CONFIG submenu appears 84
- The UNIT CONFIG Submenu 85
- The Comm Port Settings 86
- The NET CONFIG Menu 87
- Setting External Timing 87
- NET TIMING 88
- Enabling NET IBC 89
- The AUX CONFIG Menu 89
- ConÞguring the Data Ports 90
- The TIMESLOT CONFIG Menu 91
- 01 - - 24 92
- 01, starts to blink) 93
- TS CONF MANUAL and press 93
- Using the MONITOR Menu 95
- Using the TEST Menu 96
- 2 To end the test, press 97
- Sending a Test Pattern 98
- 0 and can 99
- Pattern Options 100
- LAMP Test 101
- Diagnosing 103
- Running Diagnostic Tests 104
- The Diagnostics Menu 105
- Test Parameters 106
- Test Types 108
- Loop NET Test 109
- Loop Payload Test 110
- Send 1:2 Test 112
- Appendix 113
- Technical SpeciÞcations 113
- Technical SpeciÞcations A-3 115
- Terminal Supported 116
- Equipment Grounding Conductor 116
- Front Panel LEDs and Buttons 116
- Technical SpeciÞcations A-5 117
- Factory Default ConÞguration 119
- ConÞguration Worksheet 120
- DL600E Model Numbers 121
- Appendix B 123
- Connector and 123
- Pin Assignments 123
- E1 Network Pin Assignments 124
- DCD signal 130
- Glossary 133
- Glossary G-3 135
- DSU/CSU 137
- T1 capacity (one or 137
- DSU/CSU 138
- MIB pro 138
- QRW bit errors 139
- Glossary G-9 141
- DTE device 143
- Index I-1 145
- T1 network port 147
- X.21 format 3-17 147
Produits connexes et manuels pour Mise en réseau Digital Link DL600E E1
(140 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels